To see you current Tempo Range assignment hold down Shift button at any time and observe the loop display. Shift+ Turn Loop Size Knob = Adjust Slice Count To Toggle Freeze Mode: Press SHIFT + LOOP INĮxit Freeze Mode / Escape: Press SHIFT + LOOP OUT >Tap the FX MODE button to toggle Hybrid mode On and Off. The FX MODE button to temporarily hold Hybrid mode. In Hybrid Mode, they control Slot Volume and Slot Mute/Unmute. The FX Unit 1 and 2 button/knobs are controlling FX Unit by default Whilst Hybrid Mode is activated the Remix buttons 1-4 will trigger + mute samples or only mute Stems when Stem Decks are configured. The Remix 1-4 buttons controls Hotcue 5-8 by default. Hybrid mode they control remix deck slot 1-4 Remix buttons have Hot Cue 5-8 by default Hold Shift > The loop knobs can be used to control some more FXĭon't forget to turn it off, press Shift+Loop Active or Shift+Loop Shift + Loop In or Loop Out buttons flash. Shift + Loop Set knob again to disable the echo mod. Right Loop Set knob to activate a Ramp Delay in FX Unit 4. Shift + Loop Active again to disable the echo mod. ![]() Left Loop Active knob to activate an Echo Out delay Press a Flux or the FX mode button to deactivate Super FX mode.Įcho Mods work independent from JogFX Mode. Remix Buttons for the 4 single JogFX presets.Īutomatic Effects on the FX Unit buttons. Shift + Turn JogWheel change the 3 grouped JogFX presets (FX Unit buttons 1-2-3 indicates an active preset) Shift + Flux + Reset + Deck Display + Samples + Load Leds Flash. JogFX is active, you can use the 4 sample buttons Shift and turn the jogwheel to skip to the next preset.įX leds 1+2+3 will indicate which preset you're using. Use the FX buttons on the FX Units for Macro effects!Īre 3 preset FX combinations with this mod. When you see these leds blinking, press the Jog and turn While JogFX is activated Shift + Flux + Reset + Deck Display + Samples + Load LED’s Flash. Press Shift+Flux button to activate JogFX.įlux button to deactivate (this can be done without shift) The Jogwheel for controlling effects, Get access to instant In/out, Flashing while using Echo Mod 1/2. Once you have identified the compatible driver version for your operating system, you can download it from our Drivers & Other Files page. (right deck =Fine Adjust Tempo by 0.01 BPM Knob (left deck = Adjust Tempo Fader Range (left deck) = Fine Adjust Tempo by 0.01 BPM Shift + Press Left Knob = Activate Echo Mod 1 Turn Gain = Change Platter and Scope View Headphone Cues = Enable Scratch + Calibrate Shift + Headphone Cues = Set to Relative Mode Slot Filter parameter value Display support. Freeze Mode > Slice Count Size Display support. Native mapping support for Loop Size Display. Native mapping support for Sample Cell LED Feedback. Native mapping support for Hotcue LED Feedback. Shift On Mixer - Remix Deck Hybrid Mode - Freeze ModeįX Button 1/2 = Crossfader left/right assignments ![]() Quick load next track - FX presets - Filter On Buttons - Panic Button - 8 HotCues - Customizable Mods – AutoFX - Macro FX - Layout Selector - FX Off after loading - Adjust Tempo by 0.01 BPM - Any Player - Key Adjust - 4 FX units - Auto Switch Decks Which you can edit in the Controller Manager.Ĭode Support - Beat Tap - JogFX - Echo Mods. Improvements. It’s a straightforward but fully loaded mapping Traktor 2.11.3 update with many added features and major Used as the official thread for sharing any issues, bugs, questions,Īnd general feedback for the DJ Techtools Kontrol S4 Mk2 Custom Mapping. Learn how to update the firmware of your NI hardware in this article.This mapping is for the S4 MK 2, the S4 MK1 mapping can be found here: Note: The Device Updaters found in the Drivers page are used to update the Firmware of the hardware device itself and do not install any driver software on the computer. Older generation sound cards and controllers require specific drivers which can be found on the Drivers page. These include: Windows 10: To ensure that you can make use of the class-compliant WASAPI driver, update your operating system to the latest version as explained in this article. The operating system automatically detects the device as soon as you establish the USB connection. ![]() These don't require a driver installation in order to be recognized by your system. If you cannot find a driver for your NI controller or audio interface on our Drivers page, you are using one of our 'class-compliant' devices.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |